For the electronic call acceptance function the GN9350 can be connected to the following systems.

!IMPORTANT! The connection cables are only included in the delivery for the USB or RHL modes. For all other EHS modes a special EHS-cable must be ordered separately. For further information  See here.

SIEMENS

Openstage 40 - 80 

DHSG

To register the GN 9350 in the DG mode on your DECT-telephone, please read the instructions for registering a new external mobile part in the operating instructions for your phone.

Please test the system-authentication code of your DECT-telephone. This must be set at 0000, so that this tallies with the pre-set PIN-Code of the GN 9350.

{gnresource:HSS_Siemens-SL74-WG}Instruction: In many DECT-telephones the authentication code is already set as 0000, so that a change of code is not necessary.

{gnresource:HSS_9350_DG_Anmeldung}

Now switch the GN 9350 to the DG-registration mode. For this, take the headset our of the station and make sure that there is no radio connection! Now keep the call acceptance button and the mute button on the headset pressed down simultaneously till the ONLINE-LED on the headset begins to flash "blue on the headset.

Now the headset can do a search from your base station. (For this follow the individual steps in the operating instructions for your DECT-telephone).

IMPORTANT! If you want to register the GN 9350 again to your GN9350-Station, then the existing connection from the DECT telephone must first be deleted.

From Software V.1.25 complete function

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the " HS 2 " socket of your telephone.

2)Plug the split end of the DHSG cable into the basestation of the GN 9350. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked as "AUX" at the GN 9350 Base station.

Software setting:

Set the GN 9350 on the LCD Display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base installation:

Set the telephone setup switch (A-G) at "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Transmission volume adjustment:

Set the microphone volume in the LCD-Display at "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

As soon as the dial tone signal is heard in the headset you can attend to the call by pressing the silver colored button on the headset,and pressing the same button again will end the call.

{gnresource:HSS_GN9350_Rufannahmetaste_klein}                                                                                                                                                          

Telephone installation:

Menu > Setting > Telephone > Headset > DHSG > OK

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of your telephone that is marked with the"Headset symbol"

2)Plug the split end of the DHSG cable into the basestation of the GN 9350.The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked as "AUX" of the GN 9350 basestation.

Software setting:

Set the GN 9350 in the LCD display at "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base installation:

Set the telephone setup switch (A-G) at "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Transmission volume adjustment:

Set the microphone volume in the LCD Display at "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Take call on the headset:

As soon as the dial tone signal is heard in the headset you can attend to the call by pressing the silver colored button on the headset, and pressing the same button again will end the call.

Requirements:

{gnresource:HSS_9356_607_101_klein_web} + {gnresource:HSS_14201-10_Web_klein}

GN 9350 14201-09

Octophon Open IP 150

Octophon Open IP 160

Connection:

For connection with the MSH connection cable, proceed as follows.

2-sided end:

Plug the RJ45 connector into the jack marked "AUX" and the RJ10 connector into the jack marked "Telephone icon" on the base station of GN 9350.

2-time Y-coupling end:

Plug the 3.5 mm ring connector into the headset jack and the RJ12 connector into the ring jack of the device. The additional slide-on receptacle on the Y-coupling should remain free during connection to an IP device!

IMPORTANT! The functionn "Headset" may not be activated on the device, since otherwise no remote call acceptance function will be possible!

Software setting:

Set the GN 9350 on the LCD display to "MSH" To confirm the software set, press the OK button.

Base setting:

Set the telephone-set-up switch (A-G) to "A "

Setting transmission volume:

Set the microphone volume on the LCD-display to "7/12 "

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and then end the call by pressing it once more.

Important : A ring tone signal will then only be transferred if
the "Standard/Nature" ring tone signal has been set on your telephone.

Setting:

Menu > Setting > ringing tone > tune > standard or nature

Setting telephone:

Menu > Setting > telephone > ringing connector that is jack > Microphone receiver set

Nej, det er ikke muligt. Men hvis du mister eller ødelægger dit headset, kan der parres et nyt til den nuværende baseenhed.

Der er derimod konference-mulighed i GN9350, for info om dette læs den medfølgende manual til produktet eller søg "konference" i vidensdatabasen.

Connection with PC/Laptop:

1. Connect the provided USB-cable to the mini-USB jack of the GN9330USB in the base station and to a free USB-socket in your PC/Laptop.

2. The GN9330 will then be automatic, thanks to Plug&Play registered in your control panel under > Sound&Audio devices.

Plug&Play with > Windows 2000/ME/XP > Microsoft Vista (GN9330 from version I )

{gnresource:HSS_GN9330USB_Anschlussbild}

Comfort P 300 /500 IP

Connection:

1). 1) Plug one end of the DHSG-cable marked in blue into the jack marked "head set icon" of your telephone.

2.) Plug the split end of the DHSG cable into the base station of the GN 9350. Plug the RJ10 connector into the jack with the "Telephone icon " and the RJ45 connector into the jack marked "AUX" on the GN 9350 base station.

Software setting:

Set the GN 9350 in the LCD display to"DHSG" and press the OK button.

Base setting:

Set the telephone-set-up switch (A-G) to "A"

Setting transmission volume:

Set the microphone volume in the LCD-display to "7/12" and press the OK button.

Setting telephone:

In addition a headset button must be set on Comfort Pro.

Enable Menu > Entire menu > Telephone settings > Headset

Acceptance of calls on the headset:

As soon as the ringing tone signal is heard in the headset, you can accept the call by pressing the silver colored button on the headset and end the call by pressing it once again.

Requirements:

{gnresource:HSS_9356_607_101_klein_web}       +          {gnresource:HSS_14201-09_Web_klein}
GN 9350 14201-09


{gnresource:HSS_Alcatel_logo_klein}
{gnresource:HSS_Alcatel_Touch4029_klein}

IP Touch 4028

IP Touch 4038

IP Touch 4068


Connection:


2-sided end:

Plug the RJ45 connector into the socket marked "AUX" and the RJ10 connector into the jack marked "telephone icon" on the base station of GN 9350.

2-sided Y-coupling End:

Plug the 3.5 mm ring connector into the headset jack and the RJ12 connector into the ring socket of the device. The additional slide-on receptacle at the Y-coupling should remain free during connection to an IP device!

{gnresource:HSS_alcatel_ehook_telefon_ip_klein}

IMPORTANT!The function "Headset" may not be activated on the device, since otherwise the remote call acceptance function will not be possible !

Software setting

Set the GN 9350 in the LCD display to "MSH" and press the OK button.

{gnresource:HSS_9350_Men_EHS}


Base setting:

Set the telephone-setup switch (A-G) to"A"

{gnresource:HSS_GN9350_telefon_setup_schalter}


Setting transmission volume:

Set the microphone volume on the LCD display to"7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Call acceptance on the Headset

As soon as the ringing tone signal is heard in the Headset, you can talk by pressing the silver colored button on the Headset, by re-pressing it the call is ended.

Important : A ring tone signal will then only be transferred if

the "Standard/Nature " ring tone signal has been set on your telephone.

Setting:

Menu > Setting > ringing tone > tune > standard or nature

Setting telephone:

Menu > Setting > telephone > ringing jacket or socket > Microphone receiver set

Requirements:

{gnresource:HSS_9356_607_101_klein_web}   +     {gnresource:HSS_14201-09_Web_klein}
GN 9350 14201-09


{gnresource:HSS_Alcatel_logo_klein}

{gnresource:HSS_Alcatel_Touch4029_klein}

Touch 4029
Touch 4039


Connection:


2-sided end:

Plug the RJ45 connector into the jack marked "AUX and the RJ10 connector into the jack marked " telephone icon" on the base station of GN 9350

2-sided Y-coupling end:

Plug the 3.5 mm ring connector into the "Headset jack" and the RJ12 connector into the ring jack of the device. Now plug the telephone line of the device directly into the additional connecting jack of the Y-cable

{gnresource:HSS_alcatel_ehook_telefon_klein}

!IMPORTANT!! The "Headset" function may not be enabled on the device, since the acceptance of call does not function on the headset!

Software setting

Set the GN 9350 on the LCD display to "MSH" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-setup switch (A-G) to"A"

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume on the LCD display to "7/12 "

{gnresource:HSS_9350_Men_Lautstrke}

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once more.

Important : A ring tone signal in the headset will then only be transferred if
the " Standard/ Nature" ring tone signal has been set on your telephone.

Setting:

Menu > Settings> ring tone > tune > Standard or nature

Setting telephone:

Menu > Setting > telephone > ringing jacket that is jack > Microphone receiver set

Forudsætning:

{gnresource:HSS_9356_607_101_klein_web} + {gnresource:HSS_14201-10_Web_klein}

GN 9350   +  14201-10 DHSG-cabel

{gnresource:HSS_elmeg_funkwerk_logo}

{gnresource:HSS_C290_klein}

Elmeg CS 410

Elmeg CS 290-U

Elmeg CS 410-U

Important: Det er ikke muligt at opnå EHS funktion på en Elmeg CS410 med tilsluttet telefonsvarer-modul.

Tilslutning:

1) Tilslut DHSG-kablets ende markeret med et blåt bånd i headsetudgangen på din Elmeg telefon.

2) Tilslut den 2-delte ende af DHSG-kablet i basestationen på GN9350e. Det smalle modularstik tilsluttes i udgangen markeret med en telefon, det brede modularstik tilsluttes udgangen markeret med AUX.

{gnresource:HSS_GN_9350_ehs_elmeg_cs410}

Software opsætning:

Sæt GN9350e til DHSG-mode på LCD-displayet under låget på basen. Husk at trykke "OK" efter flytning af pil.

{gnresource:HSS_9350_Men_EHS}

Base opsætning:

Sæt GN9350e's termingerings-pal på "A", under låget på basen..

{gnresource:HSS_GN9350_telefon_setup_schalter}

Indstil mikrofons volume:

Sæt GN9350e's mikrofon volume til 7/12, under låget på basen.

{gnresource:HSS_9350_Men_Lautstrke}

Opsætning telefon:

1)Aktivering af DHSG-funktion:

Tryk følgende kombination på din Elmeg telefon:

>MENU > ACCOUSTIC>HEADSET>DECT HEADSET (DHSG)

2) Programmer headset tast:

Du kan indstille dette via den medfølgende CD eller via følgende tastekombination:

Først indtast følgende kode:

**46782551## Tryk derefter følgende:

>ESC>MENU> NUMBERPROGRAMMING>TARGET SELECTION>FUNCTION

Tryk derefter på en vilkårlig hukommelses-tast, og opsæt headset funktionen.

GN9350 kan benyttes både på den almindelig fastnet telefon, samt din PC eller bærbare.

Telefon tilslutning:

1. Afmonter røret fra telefonen og sæt den i GN9350's base hvor der er markeret et "rør" (Dette gøres ikke hvis din telefon har en headsetudgang.

2. Tilslut mellemkablet bag på telefonen, enten der hvor røret sad før eller i telefonens headset-udgang.

3. Tilslut strømforsynignen til basen og sæt den i et ledigt stik i væggen.

Tilslutning til PC/bærbar:

1. Tilslut det medfølgende USB-kabel i mini-usb stikket på GN9350 basen, samt i en ledig USB port på din PC/Bærbare.

2. Plug & Play vil nu automatisk tilføje GN9350 til dit kontrolpanel under >lyde & audio opsætning)

Plug&Play fungerer på:

Windows 2000/ ME/ XP

Microsoft Vista (GN 9350 starting at Version I)

Mac OS starting from 9.0.4 to 10.1.3

Suse Linux from Kernel 9.0 onwards;

{gnresource:HSS_GN9350_Anschlussbild}

Requirements:

{gnresource:HSS_9356_607_101_klein_web}+ {gnresource:HSS_14201-09_Web_klein}

GN 9350                      14201-09


{gnresource:HSS_logo_t_com}


{gnresource:HSS_telefon_octophon_open}
Octophon Open 141

Octophon Open 151


Connection:

For the connection to the MSH connection cable, proceed as follows.

2-sided end:

Plug the RJ45 connector into the jack marked "AUX" and the RJ10 connector into the jack marked "telephone icon" on the base station of GN 9350.

2-sided Y-coupling End:

Plug the 3.5 mm "ring connector into the headset jack and the RJ12 connector into the ring jack of the device. Following this, plug the telephone wire into the West jack on MSH-cable.

{gnresource:HSS_alcatel_ehook_telefon_ip_klein}

IMPORTANT! The function "Headset" may not be activated on the device, since otherwise no remote call acceptance function will be possible!

Software setting

Set the GN 9350 in the LCD display to "MSH" and press the OK button.

{gnresource:HSS_9350_Men_EHS}


Base setting:

Set the telephone-set-up switch (A-G) to "A"

{gnresource:HSS_GN9350_telefon_setup_schalter}


Setting transmission volume:

Set the microphone volume in the LCD display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Acceptance of calls on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once again.

Menu > Setting > ringing tone > tune > standard or nature

Important : A ring tone signal in the headset will then only be transferred if

the "Standard/Nature" ring tone signal has been set on your telephone.

Setting telephone:

Menu > Setting > telephone > ringing connector or jack > Microphone receiver set

Requirements:

{gnresource:HSS_9356_607_101_klein_web}   +   {gnresource:HSS_14201-11_Web_klein}
GN 9350                          14201-11

{gnresource:HSS_Tenovis_Logo_klein}


{gnresource:HSS_T3comfort}

Tenovis T3 / T3IP Comfort / Classic

Important: On the T3 models a CTI AUDIO LINK Adapter will always be required,
and for the T3 IP models, you will require the CTI IP AUDIO LINK Adapter.

Equipment:

Integral 33/55

Integral 3/5


Connection:

One-sided end

Plug one end of the AEI cable into the jack marked AEI of the CTI Link adapter

2-sided end:

Plug the 4 pin RJ10 connector into the complete "telephone icon"
and the 8 pin RJ45 connector into the jack marked "AUX" on the GN9350 base station.

{gnresource:HSS_GN_9350_ehs_Tenovis}

Software setting:

Set the GN9350 on the LCD display to "AEI" for confirmation of the software set and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone set-up switch (A-G) on "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume on the LCD display to "7/12" and press the OK button.

{gnresource:HSS_9350_Men_Lautstrke}

Setting on the telephone device:

For integral 33/55 - telephone T3 comfort or T3 classic and T3IP

In the service menu under setting/ CTI-Audio Link or CTI-IP-Audio-Link Comfort headset must be set to AEI.

For integral I3-telephone TH, TM and TS13 from software E5.200

Setting 13-equipment: With Kz07 set the variable 2 (AEI with call signal)
                                   and Kz38 set the variable 8 (release of the headset)

Settings on the device: In the telephone menu > telephone setting > headset "on"

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button at the headset end the call by pressing it once more.

Requirements:

{gnresource:HSS_9356_607_101_klein_web} + {gnresource:HSS_14201-10_Web_klein}+ {gnresource:HSS_Akustikadapter-Bild-WG}

GN 9350     14201- 10 DHSG-cable     Acoustic-adapter (min. as-built status 10)

{gnresource:HSS_Siemens-Schrift-Bild-WG}

Opti point 410 standard / advance

Opti point 420 standard / advance

Opti point 500 basic/ standard / advance

Opti Point 600

+ Opti Point Acoustic Adapter (min version 10)

+ HiPath Telefonanlage

HiPath   500 ab V.5

HiPath 1220 ab V2.1 Build 032

HiPath 2000 ab V1.0

HiPath 3000 ab V3 SMR 14

HiPath 3000 ab V4 SMR 7

HiPath 4000 ab V1

(IMPORTANT: If any of the components are missing, the electronic call acceptance function will not work!)

Connection:

1) Plug the one-sided end of the DHSG-cable marked in blue into the jack marked "headset icon" of the OptiPoint Acoustic adapter.

2) Plug the split end of the DHSG-cable into the base station of the GN 9350. Plug the RJ10 connector into the jack marked with the complete " telephone icon " and the RJ45 connector into the jack marked "AUX " on the GN 9350 base station.

{gnresource:HSS_GN_9350_ehs_Siemens}

Software adjustment:

Set the GN 9350 on the LCD display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-set-up switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume on the LCD-display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Setting on the telephone:

Important! As soon as the headset has been connected and set, a Reset must be carried out with OptiPoint, so that the EHS function can be accepted.

Optionally, head set button can be installed via the menu on the telephone (combination: *91 select > button change > button > headset > OK).

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once more.

GN 9350GN 9350             +       14201-10 DHSG-cable

Comfort pro P 100 /300 /500

Connection:

1.) Plug one end of the DHSG-cable marked in blue into the jack marked "Headset icon" of your telephone.

Software setting:

Set the GN 9350 in the LCD display to "DHSG" and press the OK button.

Base setting:

Set the telephone-set-up switch (A-G) to "A"

Setting transmission volume:

Set the microphone volume in the LCD-display to "7/12" and press the OK button.

Setting telephone:

In addition a headset button must be set on Comfort Pro.

Menu > Entire menu > Setting telephone > Enable headset


Acceptance of call at the headset:

As soon as the ringing tone signal is heard in the Headset, you can acept the call by pressing the "silver colored button" on the headset, the call is ended by repressing it.

Requirements:

{gnresource:HSS_9356_607_101_klein_web}     +      {gnresource:HSS_AZ-Adapter-Bild-WG} + {gnresource:HSS_DE-EHS001_klein}
GN 9350                           AZ-Adapter                          DE-EHS-001
GN 9330

{gnresource:HSS_Detewe_logo}

{gnresource:HSS_OpenPhone65-WG}

open phone 63/65


Equipment:

Open Com 100 from software 5.2
Open Com 1000 from software 3.2


Connection:

Connect the 4-pinned RJ10 cable provided to the RJ10 jack marked "phone icon" marked jack on the base station of the GN9350 and the other end to the "Head set jack" of the A-Z adapter.

Now plug the 8-pinned RJ45 connector of DE-EHS-001connector cable into the socket marked "AUX" on the GN 9350 base station.

Connect the Hollow socket plug to the A-Z jack adapter marked "ring symbol" and the 6-pin West plug into the "second jack" of the A-Z adapter.


Setting software:

Set the GN 9350 in the LCD-display to "RHL" and press the OK button.

{gnresource:HSS_9350_Men_EHS}


Setting base:

Set the telephone setup switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}


Setting transmission volume:

Set in the LCD-display the microphone volume to 7/12 and press the OK button.

{gnresource:HSS_9350_Men_Lautstrke}


Setting on open 63/65

Activate the function "Remote Headset" on your Open Phone set as follows.
Now type in the following key combination into your Open 63/65 phone:

> MENU > SETTING > PERIPHERAL > additional device-selection >
"REMOTE HEADSET"

Call acceptance on the Headset

As soon as the ringing tone signal is heard in the Headset, you can talk by pressing the silver colored button on the Headset, by re-pressing it the call is ended.

Forudsætning:

{gnresource:HSS_9356_607_101_klein_web}+    {gnresource:HSS_EHS-AV-001II}

GN 9350                   EHS-AV-001

Callmanager fra Software 4.0 og op.

Prerequisite:

{gnresource:HSS_9356_607_101_klein_web}  +   {gnresource:HSS_HHC-Adapter_Cisco_IP}

Cisco 7942 G
Cisco 7945 G
Cisco 7962 G
Cisco 7965 G
Cisco 7975 G

The HHC adapter requires the Cisco Unified Communication Manager 4.1(3), or a higher version and the telephone firmware 8.3(3).

2) Connect the HHC adapter to the "AUX " socket of your Cisco Instrument and the "AUX" interface of your GN9350 basestation.

Set GN 9350 in the LCD display at "DHSG" Installation of the software is confirmed by pressing the OK button.

Set the telephone setup switch to "B".

Adjustment of the transmission volume:

On the LCD display set the microphone volume to " 7 / 12 "

{gnresource:HSS_9350_Men_Lautstrke}

Call receipt on the headset:

As soon as the call tone signal is heard on the headset you can take the call by pressing the " silver-colored button " on the headset. Pressing the same button again will end the call.

Necessary setting at the Communication-Manager:

Under the item "Devices" call receipt "Wireless Headset Hookswitch Control" must be enabled for each of the end devices.

Prerequisite:

{gnresource:HSS_9356_607_101_klein_web} +     {gnresource:HSS_EHS-AV-001II}

GN 9350                   EHS-AV-001

This combination is compatible with the following Avaya instruments:

4610 / 4620

4621 / 4622

4625 / 4630

5420 / 5620

3) Plug the 4-pin connection cable into the socket marked with the "Telephone symbol" on the basestation of the GN 9350 and the opposite side into the "Headset interface" of your telephone.

4) Now you can re-connect the network cable to the telephone.

Software setting:

Set the GN 9350 in LCD display at "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base installation:

Set the telephone setup switch (A-G) at "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Transmission volume adjustment:

Set the microphone volume in the LCD display to "7/12".

Call reception on the headset:

As soon as the ringtone signal is heard in the headset you can answer the call by pressing the silver-colored button on the headset, and pressing the same button again will end the call.

1) Plug the 1-sided end of the DHSG-cable that is marked in blue into the socket of your telephone which is marked with a"headset symbol"

2) Plug the split end of the DHSG cable into the basestation of GN 9350. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked with "AUX" at the GN 9350 Base station.

Software setting:

Set the GN 9350 in LCD Display at "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-setup switch (A-G) to "A".

Adjustment of transmission volume :

Set the microphone volume in the LCD-Display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Telephone setting:

Open Phone 71                        Menu > Settings > Audio > Headset ON

Open Phone 73 / 75 incl. IP:  Menu > Overall menu > Telephone setting > Headset ON

Call reception on the headset:

As soon as the dial tone signal is heard in the headset you can take the call by pressing the silver colored button on the headset, and the call is ended by pressing it again                                                               

Requirements:

{gnresource:HSS_9356_607_101_klein_web} + {gnresource:HSS_14201-10_Web_klein}

GN 9350 + 14201-10 DHSG-cable

{gnresource:HSS_logo}

{gnresource:HSS_innovaphone_IP230_klein}

Innovaphone IP 230

Connection:

1) Plug one end of the DHSG-cable marked in blue into the jack marked ""head set icon" of the Innovaphone IP 230.

2) Plug the split end of the DHSG cable into the base station of the GN 9350. The RJ10 connector in the jack to the complete " Telephone icon " and the RJ45 connector to the jack marked "AUX" on the GN9350 base station.

{gnresource:HSS_GN_9350_ehs_innovaphone_IP_230}

Software setting:

Set the GN 9350 on the LCD display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-set-up switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume in the LCD-display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once more.

GN 9350           +     14201-10 DHSG-cable     +     Universal-adapter

Comfort open P 100 /300 IP

Important:

Comfort Open

Connection:

1) Plug one end of the DHSG-cable marked in blue into the jack marked
"Headset icon" of the universal adapter.

2) Plug the split end of the DHSG-cable into the base station of the GN 9350. Plug the RJ10 connector into specified jack with the "telephone icon" and RJ45 connector into the jack marked "AUX" on the GN 9350 base station.

Software setting:

Set the GN 9350 on the display to "DHSG" and press the OK button.

Base setting:

Set the telephone-set-up switch (A-G) to "A"

Set the microphone volume on the LCD-display to "7/12 " press the OK button.

Setting telephone:

In addition a headset button must be set on Comfort Open.

Important: As soon as the headset has been connected and set, then a Reset must be carried out with the OptiPoint, so that the EHS function can be accepted

Acceptance of calls on the headset:

As soon as the ringing tone signal is heard in the headset, you can accept the call by pressing the silver colored button on the headset and end the call by pressing it once again.

Answering a call on the headset:

As soon as an incoming call is heard by a signal tone in the headset, you can answer the call by pressing the black answer button on the headset, the call can be ended by pressing the same button once again.

Requirements:

{gnresource:HSS_9356_607_101_klein_web} + {gnresource:HSS_14201-10_Web_klein}

GN 9350   +  14201-10 DHSG-cable

{gnresource:HSS_agfeo_logo}

{gnresource:HSS_Agfeo_ST40}

Agfeo ST31
Agfeo ST40

Connection:

1) Plug the one-sided end of the DHSG-cable marked in blue into the jack marked "head set icon" of the Agfeo ST40.

2) Plug the split end of the DHSG-cable into the base station of the GN 9350. Plug the RJ10 connector into the jack marked with the " telephone icon " and the RJ45 connector into the specified "AUX" jack on the GN 9350 base station.

{gnresource:HSS_GN_9350_ehs_agfeo_st40}

Software setting:

Set the GN 9350 on the LCD display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-set-up switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume on the LCD-display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once again.

The GN9350 is provided with a standard-cable connection for the handset jack and a mini-USB to USB-cable. For the separate electronic call acceptance function a special connection cable must also be ordered in each case.

You can look up the respective mode in the EHS overview or in our checklist.

Requirements:

{gnresource:HSS_9356_607_101_klein_web} +      {gnresource:HSS_14201-10_Web_klein}  +        {gnresource:HSS_Akustikadapter-Bild-WG}

GN 9350            14201-10 DHSG-cable      Universal-adapter

Octophon F 20 / 30 / 40 / 50

Octophon F IP 21 / 31 / 41

+ Adapter Universal (min version 10)

+ Octophon F Telefonanlage

Octophon F 200 - 900

(IMPORTANT: If any of the components are missing, the electronic call acceptance function will not work!)

Connection:

1) Plug the one-sided end of the DHSG-cable marked in blue into the jack marked "head set icon" of the Universal adapter.

2) Plug the split end of the DHSG cable into the base station of the GN 9350.
The RJ10 connector into the jack marked with the complete "Telephone icon" and the RJ45 connector into the jack marked "AUX" on the GN9350 base station.

{gnresource:HSS_GN_9350_ehs_Siemens}

Software setting:

Set the GN 9350 on the LCD display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-set-up switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume on the LCD-display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Setting on the telephone:

Important! As soon as the Headset has been connected + adjusted a Reset must be carried out on the OptiPoint, so that the EHS function is accepted

Optionally a head set button can be installed via the menu on the telephone (combination: *91 select > button change > button > headset > OK ).

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once more.

Telefon tilslutning:

1. Tilslut den medfølgende mellemledning i telefonens headsetudgang (hvis en sådan ikke findes benyttes telefonens rørudgang).

2. Tilslut den anden ende af ledningen i GN9330e's base hvor der er markeret en telefon.

3. Tilslut strømforsyningen til GN9330e's base samt i en stik-kontakt. 

{gnresource:HSS_GN9330_Anschlussbild}

{gnresource:HSS_9350_Men_klein}

You will find following 5 icons on the LCD display:

{gnresource:HSS_9350_Men_Lautstrke} Mikrofonlautstärke

You can turn your microphone up or down with this icon.

{gnresource:HSS_9350_Men_EHS}AUX-Setting

With this icon you can set different types of answers via the AUX-port. The setting on GN_RHL is for operation with GN1000 or for the connection via the receiver device.

{gnresource:HSS_9350_Men_Funk} operating distance

With this icon you can set your range + max radiance of the GN 9350. Normal = up to 100m / to 64mW; low = up to 30m / to 4mW; very low = up to 10m/1mW

{gnresource:HSS_9350_Men_klein}tone color

With this icon you can set the tone color of your headset. Here you can select between high and low and between wide band and narrow band quality.

{gnresource:HSS_9350_Men_DSP} adjustment of DSP (GN8210)

With this icon you can set your hearing protection, i.e. enable and disable.

Level 0 = DSP is switched off

Level 1 = telephony till 4hrs

Level 2 = telephony till 84hrs

Level 3 = telephony is more than 8hrs

Level 4 = TT4 standard

Requirements:

{gnresource:HSS_9356_607_101_klein_web}     +          {gnresource:HSS_AZ-Adapter-Bild-WG} + {gnresource:HSS_DE-EHS001_klein}   

         GN 9350                        Comfort-Adapter                      DE- EHS-001
         GN 9330


{gnresource:HSS_logo_t_com}


{gnresource:HSS_T-comfort-830-Bild-WG}

T-Comfort 730

T-Comfort 830


Equipment:

T-Comfort DSL 930

Connection:

Connect the supplied 4 pin cable RJ10 with the RJ10 in the jack marked " Telephone icon" on the base station of the GN 9350 and the opposite end to the "headset jack" of the A-Z adapter.

Now plug the 8 pin RJ45 connector of the DE-EHS 001 cable connection into the "AUX" jack on the GN 9350 base station.

Connect the hollow socket plug to the jack marked "ring icon" of the A-Z adapter and plug the 6 pin West connector into the "second receiver jack" of the A-Z adapter.

Software setting:

Set the GN 9350 on the LCD display to "RHL" To confirm the software set, press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone set-up switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume on the LCD-display to " 7/12" and press the OK button.

Setting on the T-Comfort device:

Activate the "remote headset" function in the telephone menu for electronic call acceptance on the headset. For this, key in the the following combination on the device:
Menu> Setting > Periphery > z Additional device-selection >
" REMOTE HEADSET "

From Equipment Software 6.0:

Enable the DECT HEADSET function in the telephone menu.

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once more.

Call reception from the CISCO IP Communicator:

Prerequisite:

9350 // 9330 USB +

CISCO IP Communicator V2.0 +

Driver for  9350 // 9330 USB (download here)

Installation:

Plug in the GN9350 // GN9330USB  cordless headset to a free USB port on your PC or laptop With the help of Plug&Play function. This will subsequently automatically find and install 9350 // 9330USB .

Now load the driver in the Support-area of 9350 // 9330USB here from Online-Support and save these to your desktop.If the CISCO-IP communicator is open, please close it now, .

Now you can start the driver and please follow the instruction on the screen.

The Headset and the driver are now successfully installed and you can activate your Softphone again. Now with the help of the "Audio Tuning Wizard" register the 9350 // 9330USB as reproducer and finally make the audio adjustments in Wizard.

Now the device is functional

1) Plug the 1-sided end of the DHSG-cable that is marked in blue into the socket of your telephone which is marked with a "Headset symbol"

2) Plug the split end of the DHSG-cable into the base station of GN 9350. Plug the RJ10 plug into the socket with the complete "Telephone symbol" and the RJ45 plug into the socket marked with "AUX" at the GN 9350 Base station.

Software setting:

Set the GN 9350 the in LCD Display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone-set-up switch (A-G) to "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Adjustment of transmission volume :

Set the microphone volume in the LCD-Display to "7/12".

{gnresource:HSS_9350_Men_Lautstrke}

Telephone setting:

Menu > Settings > Audio > Headset ON

Call reception on the headset:

As soon as the dial tone signal is heard in the headset you can take the call by pressing the silver colored button on the headset, and the call is ended by repressing it                                                               

Requirements:

{gnresource:HSS_9356_607_101_klein_web}     +   {gnresource:HSS_14201-11_Web_klein}
GN 9350 14201-11

{gnresource:HSS_Tenovis_Logo_klein}

{gnresource:HSS_tenovisTM13-WG}

Tenovis TM/TH13 Comfort /Classic


Equipment:

Integral 3 (from software E5.200)

Integral 5

Integral 33 / 55

The electronic call acceptance function on the TS13 is only possible in connection with an Integral 3


Connection:

1-sided end:

Plug one end of the AEI cable into the jack marked X/Y
of your telephone

2-sided end:

Plug the RJ10 connector into the jack marked with the complete telephone icon and the 8-pin RJ45 connector into thejack marked "AUX" on the GN 9350 base station

{gnresource:HSS_GN_9350_ehs_Tenovis}

Software setting:

Set the GN 9350 on the LCD-display to "AEI" to confirm the software set, press the OK button.

{gnresource:HSS_9350_Men_EHS}


Base setting:

Set the telephone-setup switch (A-G) to "A"

{gnresource:HSS_GN9350_telefon_setup_schalter}

Setting transmission volume:

Set the microphone volume in the LCD-display to " 7/12" and press the OK button.

{gnresource:HSS_9350_Men_Lautstrke}


Setting on the telephone device:

For integral 33/ telephone TH13 and TM13

In the service menu with other functions > further settings >
to "headset/AEI" "one" > and the operation type to "Y ESTI AT".


For integral 13 telephone TH, TM and TS13 from software E5.200.

Setting 13-equipment: With Kz07setthe variable 2 (AEI with calling signal)
                                   and Kz38 setthe variable 8 (=Release headset)

Settings on the device: In the telephone menu> telephone setting> headset "on"

Call acceptance on the headset:

As soon as the ringing tone signal is heard in the headset, you can talk by pressing the silver colored button on the headset and end the call by pressing it once more.

GN 9350               14201-10 DHSG-cable

OpenStage 40 / 60 / 80

Connection:

1) Plug the 1-sided end of the DHSG cable marked in blue into the socket of your OpenStage instrument marked with the
" Headset symbol " .

2) Plug the split end of the DHSG cable into the basestation of the GN 9350.
The plug of the RJ10 is plugged into the socket with the complete " Telephone symbol " and RJ45 is plugged into the socket marked " AUX " on the GN 9350 basestation.

Software setting :

Set GN 9350 in LCD display on" DHSG " Installation of the software is confirmed by pressing the OK button.

Set the telephone setup switch at "A".

Adjustment of the transmission volume:

Set the microphone volume in LCD display at " 7 / 12 "

Call reception on the headset:

As soon as the call tone signal is heard on the headset you can take the call by pressing the " silver colored button " on the headset and pressing the same button will end the call.

Important:: The dial tone signal in the headset is transmitted only when the standard ringtones are used on your telephone. No "call signalling" for mp3-ringtones

Prerequisite:

{gnresource:HSS_9356_607_101_klein_web} +     {gnresource:HSS_snom_360}    +     {gnresource:HSS_snom_ehs_adapter(1)}

GN 9350                Snom 320*/360*/370**         Snom EHS Box

(*Snom 320/360 > ab Software release 6.5.8 nähere Infos unter http://www.snom.com/wiki/index.php/Accessories/Interface_Box )

(**Snom 370 > ab Software release 7.1.28 )

In the event of problems, download the latest software for the instrument .

Connection:

{gnresource:HSS_snom_ehs_anschluss}

1) Connect the provided RJ10 to the RJ10 connecting cable on the GN9350 with the headset-interface of the Snom instrument and the socket with the complete telephone symbol on the GN9350 basestation.

2) Connect the Snom EHS Box with the " EXT " port of your Snom instrument and the " AUX" interface on the basestation of your GN9350

Software setting:

Set the GN 9350 in LCD Display to "DHSG" and press the OK button.

{gnresource:HSS_9350_Men_EHS}

Base setting:

Set the telephone set-up switch (A-G) at "A".

{gnresource:HSS_GN9350_telefon_setup_schalter}

Adjustment of transmission volume :

Set the microphone volume on the LCD-Display at "7/12".